How to Start Bluetooth Topology Projects Using NS3

To start Bluetooth Topology simulations using NS3 those are normally attained to utilize the Low-Rate Wireless Personal Area Network (LR-WPAN) module that offers support for Bluetooth-like technologies. This module can utilize to replicate the Bluetooth Piconets, Scatternets, or custom Bluetooth topologies. Below is a detailed procedure to start and simulate Bluetooth Topology Projects in NS3.

Steps to Start Bluetooth Topology Project in NS3

Step 1: Set Up NS3

  1. Install NS3:
    • Go to the NS3 webpage to download NS3.
    • Build NS3:

./waf configure

./waf build

  1. Verify Installation: Confirm NS3 including simple instance:

./waf –run scratch/my_first

  1. Enable the LR-WPAN Module: Make sure that the LR-WPAN module is allowed:

./waf configure –enable-modules=lr-wpan

./waf build

Step 2: Understand Bluetooth Topology

  • Common Bluetooth Topologies:
    • Piconet: A single master associates to several slave devices.
    • Scatternet: Numerous connected piconets including delivered devices to perform like bridges.

Step 3: Plan the Topology

  1. Define the structure:
    • We can describe the volumes of devices must have 7 devices: 1 master and 6 slaves for a piconet.
    • Deployment area such as 10×10 meters for short-range interaction.
  2. Decide communication type:
    • We need to select the peer-to-peer, broadcast, or master-slave communication.
  3. Set simulation goals:
    • To measure the metrics like throughput, latency, and energy consumption.

Step 4: Set Up the Bluetooth Topology

  1. Create Nodes: Describe the nodes for Bluetooth devices.

NodeContainer nodes;

uint32_t numDevices = 7; // 1 master and 6 slaves

nodes.Create(numDevices);

  1. Set Up Bluetooth (LR-WPAN) Devices: Set Bluetooth-like interaction to utilize the LR-WPAN module.

LrWpanHelper lrWpanHelper;

// Install LR-WPAN devices on nodes

NetDeviceContainer devices = lrWpanHelper.Install(nodes);

// Assign MAC addresses

lrWpanHelper.AssociateToPan(devices, 0); // All devices in the same PAN

  1. Set Up Node Mobility: In small area, set up nodes to replicate the limited range of Bluetooth.

MobilityHelper mobility;

mobility.SetPositionAllocator(“ns3::GridPositionAllocator”,

“MinX”, DoubleValue(0.0),

“MinY”, DoubleValue(0.0),

“DeltaX”, DoubleValue(2.0),

“DeltaY”, DoubleValue(2.0),

“GridWidth”, UintegerValue(3),

“LayoutType”, StringValue(“RowFirst”));

mobility.SetMobilityModel(“ns3::ConstantPositionMobilityModel”);

mobility.Install(nodes);

  1. Install Internet Stack (Optional): Insert an Internet stack for IP-based interaction as needed.

InternetStackHelper stack;

stack.Install(nodes);

Ipv4AddressHelper address;

address.SetBase(“10.1.1.0”, “255.255.255.0”);

Ipv4InterfaceContainer interfaces = address.Assign(devices);

Step 5: Simulate Traffic

  1. Set Up Applications: We need to describe the traffic flows among the master and slave devices.
    • UDP Echo Example:

UdpEchoServerHelper echoServer(9); // Port 9

ApplicationContainer serverApp = echoServer.Install(nodes.Get(0)); // Master device

serverApp.Start(Seconds(1.0));

serverApp.Stop(Seconds(10.0));

UdpEchoClientHelper echoClient(Ipv4Address(“10.1.1.1”), 9); // Server’s IP

echoClient.SetAttribute(“MaxPackets”, UintegerValue(10));

echoClient.SetAttribute(“Interval”, TimeValue(Seconds(1.0)));

echoClient.SetAttribute(“PacketSize”, UintegerValue(1024));

ApplicationContainer clientApp = echoClient.Install(nodes.Get(1)); // Slave device

clientApp.Start(Seconds(2.0));

clientApp.Stop(Seconds(10.0));

  1. Use Flow Monitor: Estimate the throughput, delay, and packet loss with the help of Flow Monitor.

FlowMonitorHelper flowmon;

Ptr<FlowMonitor> monitor = flowmon.InstallAll();

monitor->SerializeToXmlFile(“bluetooth_topology_flowmon.xml”, true, true);

Step 6: Run and Analyze

  1. Run the Simulation:

Simulator::Run();

Simulator::Destroy();

  1. Enable Packet Capture: We can store .pcap files for traffic analysis.

lrWpanHelper.EnablePcapAll(“bluetooth_topology”);

  1. Analyze Results: Measure the performance outcomes to utilize Flow Monitor and packet traces.

Example: Minimal NS3 Script for Bluetooth Topology

#include “ns3/core-module.h”

#include “ns3/network-module.h”

#include “ns3/internet-module.h”

#include “ns3/lr-wpan-module.h”

#include “ns3/mobility-module.h”

#include “ns3/applications-module.h”

#include “ns3/flow-monitor-module.h”

using namespace ns3;

int main(int argc, char *argv[]) {

uint32_t numDevices = 7; // 1 master and 6 slaves

// Create nodes

NodeContainer nodes;

nodes.Create(numDevices);

// Configure LR-WPAN (Bluetooth-like)

LrWpanHelper lrWpanHelper;

NetDeviceContainer devices = lrWpanHelper.Install(nodes);

lrWpanHelper.AssociateToPan(devices, 0);

// Configure mobility

MobilityHelper mobility;

mobility.SetPositionAllocator(“ns3::GridPositionAllocator”,

“MinX”, DoubleValue(0.0),

“MinY”, DoubleValue(0.0),

“DeltaX”, DoubleValue(2.0),

“DeltaY”, DoubleValue(2.0),

“GridWidth”, UintegerValue(3),

“LayoutType”, StringValue(“RowFirst”));

mobility.SetMobilityModel(“ns3::ConstantPositionMobilityModel”);

mobility.Install(nodes);

// Install Internet stack

InternetStackHelper stack;

stack.Install(nodes);

Ipv4AddressHelper address;

address.SetBase(“10.1.1.0”, “255.255.255.0”);

Ipv4InterfaceContainer interfaces = address.Assign(devices);

// Set up UDP echo server and client

UdpEchoServerHelper echoServer(9);

ApplicationContainer serverApp = echoServer.Install(nodes.Get(0)); // Master device

serverApp.Start(Seconds(1.0));

serverApp.Stop(Seconds(10.0));

UdpEchoClientHelper echoClient(interfaces.GetAddress(0), 9); // Server’s IP

echoClient.SetAttribute(“MaxPackets”, UintegerValue(10));

echoClient.SetAttribute(“Interval”, TimeValue(Seconds(1.0)));

echoClient.SetAttribute(“PacketSize”, UintegerValue(1024));

ApplicationContainer clientApp = echoClient.Install(nodes.Get(1)); // Slave device

clientApp.Start(Seconds(2.0));

clientApp.Stop(Seconds(10.0));

// Enable Flow Monitor

FlowMonitorHelper flowmon;

Ptr<FlowMonitor> monitor = flowmon.InstallAll();

monitor->SerializeToXmlFile(“bluetooth_topology_flowmon.xml”, true, true);

// Enable packet capture

lrWpanHelper.EnablePcapAll(“bluetooth_topology”);

// Run simulation

Simulator::Run();

Simulator::Destroy();

return 0;

}

We outlined the project’s guiding methodology for simulating Bluetooth Piconets, Scatternets, or custom Bluetooth topologies using LR-WPAN module in NS3 tool.

We give you a detailed procedure to start and simulate Bluetooth Topology Projects in NS3 tool , Our developers can help you complete your project performance. Share with us all your project details to receive best guidance.